Produkty dla na produkty (51)

SS 420 is a heat treatable martensitic chromium stainless steel. Melt practice is controlled to develop a surface nearly free from defects. It provides the best combination of wear resistance and corrosion resistance, and is used in demanding medical accessories, such as high quality surgical instruments. The alloy can be cold formed from the annealed temper.Welding should be accomplished by pre and post heating.Pre-heating at 450° F and post-heated at 1300° F will prevent cracking. The corrosion resistance is optimized in the heat treated temper and assured by passiviation. It is resistant to water and organic materials. Oxidation resistance remains favorable in most applications up through 1200°F. Density:0.28 lbs/cu.in. Melting Point (Approx.):1460°C Electrical Resistivity @ R.T.:55 Microhm·cm Thermal Expansion Coefficient (0° to 100°C):10.3 x 10-6/°C Thermal Conductivity @ 100°C:24.9 W/m·K Magnetic Permeability (Annealed: H= 200 oersteds):Yes

Superior Tube is committed to improving healthcare options for patients, and to helping surgeons save lives. As such, we manufacture a range of specialized welded and seamless tubing products for various areas of the medical device industry, including cardiac stents. Stents are small, expandable tubes, usually made of metal mesh, and are used to treat narrowed or weakened arteries. In patients with coronary heart disease, stents are implanted in order to open narrowed arteries during a procedure called percutaneous coronary intervention, or angioplasty. Heart stents can also help relieve chest pain and aid in the prevention of heart attacks. Ever since our tubing was used in the earliest cardiac stent implants in 1987, Superior Tube has been an industry leader in the manufacture of implant grade tubing for both coronary and peripheral stents. Please note that we have a minimum order value of £10,000.

SS 17/7 PH® is a precipitation hardenable stainless steel that is formable and also capable of meeting high strength requirements. It is utilized in applications that require both high strength and good corrosion resistance. The alloy is classified as semi-austenitic to distinguish the soft phase (austenite) available for ease of forming from the high strength phase (martensite) usually achieved by heat treatment. The alloy can be formed from the annealed temper but due to a rapid work hardening rate may not be deep drawn without intermediate annealing. It is joined by most arc and resistance methods used for stainless steel. It should not be fusion welded unless shielded by inert gas to prevent oxidation of aluminum. Density (Heat Treated):0.276 lb/cu.in. Electrical Resistivity (Heat Treated):83 Microhm·cm Thermal Conductivity @ 150°C:16.7 W/m·K Magnetic Attraction:None

MP35N* is an age hardenable nickel-cobalt base alloy that has a unique combination of properties - ultra high strength, toughness, ductility and outstanding corrosion resistance. MP35N resists corrosion in hydrogen sulphide, salt water and other chloride solutions. It also has excellent resistance to crevice and stress corrosion cracking in sea water and other hostile environments. Suitable where a high combination of strength, high modulus values and good corrosion resistance are required. Applications for this alloy also include medical devices and dental products. Please note that we have a minimum order value of £10,000. Specific Heat (0-100°C):502 J/kg/°K Thermal conductivity:11.2 W/m/°K Thermal Expansion:12.8 μm/μm/°C Modulus Elasticity:234 Gpa Electrical Resistivity:6.21 μohm/cm Density:8.43 g/cm3

AMETEK Specialty Metal Products has been a leader in the development of shaped wire products for use in orthodontic brackets for more than 20 years. Whether orthodontic materials are needed for a new design process to increase torque strength in orthodontic brackets, or support for a highly customized next generation project, our engineers are ready to work with you to ensure success. Advantages As a world class metal wire manufacturer, we deliver custom wire shapes, custom wire alloys and precise sizes. Our shaped wire products deliver major advantages for the manufacture of near net shape orthodontic brackets. These include: Superior dimensional control for precision bracket geometries that reduce occlusal interference and improve patient comfort Tightly controlled alloy purity, consistency and composition for improved performance Improved die wear, formability and platability Highly customized materials enable increased torque strength

SS 304L is an austenitic Chromium-Nickel stainless steel offering the optimum combination of corrosion resistance, strength, and ductility. These attributes make it a favorite for many mechanical switch components, and use in surgical instruments. Low carbon content reduces susceptibility to carbide precipitation during welding. The alloy is readily formed in the annealed temper.SS 304L may be joined by all commonly used brazing and welding methods including oxyacetylene. The corrosive resistance to acids is generally very good with the exception of halogen acids. Available Sizes: SS 304L is available from Hamilton Precision Metals as strip product in thicknesses from 0.0005” to 0.050” (0.0127 mm to 1.27 mm) in widths up to 12.0” (304.8 mm). It is also available in foil as thin as 0.000200” (0.00508 mm) in widths of 4.0” (101.6 mm) maximum. The material conforms to ASTM A240, ASTM A666, FED QQ-S-766, MIL-S-4043, UNS S30403. Density:0.284 lbs./cu.in. Melting Point (Approx.):1400°C Electrical Resistivity @ R.T.:72 Microhm·cm Thermal Expansion Coefficient (0° to 100°C):17.3 x 10-6 /°C Thermal Conductivity @ 100°C:16.3 W/m·K Magnetic Permeability (Annealed: H= 200 oersteds):1.02 Max

SS 301 is an austenitic Chromium-Nickel stainless steel capable of attaining high strength with moderate cold working. The combination of high strength and good ductility makes it suitable for numerous mechanical switches as well as surgical instruments, metal stampings and electronic and computer spring components.. The alloy is readily formed in the annealed temper. Ductility decreases with increased cold rolled strength but not to the degree that would occur with SS 302. It is not recommended for deep drawing. SS 301 can be welded by all conventional processed except oxy-acetylene. The weld should not make contact with electrolytes to prevent intergranular corrosion. SS 301 is resistant to atmospheric corrosion and is additionally resistant to mildly corrosive mediums. The combination of narrow strength bands and close thickness tolerance provided by Hamilton Precision Metals is the key to repeatable response characteristic in spring and switch applications. Density:0.287 lbs.cu.in. Melting Point (Approx.):1400°C Electrical Resistivity @ R.T.:72 Microhm·cm Thermal Expansion Coefficient (0° to 100°C):16.9 x 10-6/°C Thermal Conductivity @ 100°C:16.3 W/m·K

Evanohm® R is a unique resistance alloy with high electrical resistivity and very low temperature coefficient of resistivity (TCR). The alloy is produced by melting and conditioning practices which result in a low level of pinholes at ultra-thin thicknesses. This combination of attributes with inherent corrosion resistance makes it suitable for a variety of strain gauge, foil heaters and airbag igniters. The alloy is supplied with 90% cold reduction which has a positive TCR of about 70 PPM/ºC. A stabilizing heat treatment (approximately 475ºC) during manufacture of finished parts adjusts the TCR to a desired value. The heat treatment virtually eliminates any drift tendency of the resistivity. A heat-treat curve for each melt is developed at Hamilton and is made available as a guide in regulating TCR. Sizes Evanohm® R is available from Hamilton Precision Metals as foil and strip product in thicknesses from 0.0005” to 0.010” (0.0127 mm to 0.254 mm) and in widths up to 12.0” Density:0.293 lbs/cu.in. Melting Point (Approx.):1350°C Electrical Resistivity @ R.T:133 Microhm·cm Thermal EMF vs. Copper (0°C to 100°C):<1.0 Millivolts/°C Thermal Conductivity R.T.:14.6 W/m·K

AMETEK Specialty Metal Products is committed to meeting the demands of Metal Additive Manufacturing (AM) for mass-production of industrial components. We engineer economic AM powder of mainstream stainless steel, nickel, and cobalt alloys for non-rotor-grade components made by Laser Powder Bed, Binder Jet, and Cold Spray processes. Alloys As a leader in metal powder production for additive manufacturing, we offer several different alloys and size distributions specifically tailored for different additive manufacturing processes and machines. The most common additive manufacturing powder materials produced include: 316L (including A240 grade) 304L 17-4PH® We also offer specialty austenitic and ferritic stainless steels, as well as a selection of nickel and cobalt alloy powders for 3D printing.

Superior Tube supplies high pressure tubes that exceed current industry standards and we supply high quality products that are used in oil and gas extraction, high pressure liquid chromatography, military applications, water jet cutting, and more. Our tube mill manufactures high pressure tubing in straight lengths, and in a variety of corrosion resistant austenitic, nickel alloys, and stainless steels. Sizes run from 0.050” right up to 1.250” outside diameter, with wall thicknesses between 0.0175” and 0.218”. Operating conditions can require our products to be service rated above 60,000psi operating pressure, with tensile strengths greater than 220ksi. Please note that we have a minimum order value of £10,000.

SS 436 is a corrosion and heat resistant ferritic Chromium Steel. It can be polished to appear similar to Chromium plate. The material is magnetic in both annealed and cold rolled tempers. This grade of ferritic stainless steel has shown a greater resistance to ridging or roping defects as compared to type 430 stainless steel. The alloy can be readily blanked and formed. The material can be resistance welded, brazed, and soldered. SS 436 is resistant to atmospheric corrosion and fresh water, but it not resistant to most salts and seawater. It is resistant to scaling by oxidation up to about 1400°F. Available Sizes: SS 436 is available from Hamilton Precision Metals as strip product in thicknesses from 0.001” to 0.050” (0.0254 mm to 1.27 mm) in widths up to 15.0” (381 mm). The material conforms to ASTM A240 and UNS S43600. Density:0.28 lbs/cu.in. Melting Point (Approx.):1425°C Electrical Resistivity @ R.T.:67 Microhm·cm Thermal Expansion Coefficient (0° to 100°C):9.3 x 10-6 /°C Thermal Conductivity @ 100°C:21 W/m·K Magnetic Permeability:400 - 700

Achieving the highest quality polyester and nylon fibers requires selection of the right fiber filter media. We offer many filtration powder options for melt spun polymers. Typical Melt Spun Polymers and Corresponding AMETEK Filtration Product Polyamide / Nylon – AMETEK DP-1 Product Line Polyethylene Terephthalate (PET) / Polyester – AMETEK 316L or DP-1 Product Line Polypropylene – AMETEK 316L or DP-1 Product Line Custom Hot Polymer Filtration materials are offered for the most demanding applications Precision Powders Provide Numerous Advantages Compared to Metallic Fibers, Sand, or Glass Outstanding continuity of spin operation Premium fiber quality through superior filtration Excellent volume performance due to robustness of metal powder Correct porosity and tortuosity in filtration media for maximum hot polymer shear enabled by our advanced water atomization technology No chemical reaction with polymer, eliminating any discoloration of the fiber

Because of its strength, unique density and corrosion resistance, titanium has found applications in many industries. For high quality tubing products, it’s often a better substance to use than competing materials like stainless steels or super alloys. Titanium tubes are light weight and exceptionally corrosion and heat resistantThe density of titanium is about 60 per cent of that of steel- or nickel-based alloys giving significant weight savings in aerospace structures. The tensile strength is better than that of austenitic or ferritic stainless steels. Titanium is exceptionally corrosion resistant and exceeds the resistance of stainless steels in most environments. The metal is non-magnetic too, and has good heat transfer properties, with a melting point higher than steel alloys. Titanium is easily worked. Please note that we have a minimum order value of £10,000.

The microstructures inside duplex stainless steels are approximately 50 per cent austenite and 50 per cent ferrite, and consequently duplex products share the physical properties of both ferritic and austenitic grades. Duplex stainless steels are resistant to the cracking caused by chloride stress corrosion in austenitic grades, and have improved resistance to localised corrosion. This family of stainless steels has roughly twice the yield strength of their counterpart austenitic grades . Higher hardness values provide better wear resistance for high precision tubes. Duplex stainless steel tubes have high hardness and wear resistance propertiesDuplex steels are easily welded and formed, similar to austenitic grades. Depending on chromium, nickel and molybdenum content, duplex stainless steels are divided into four main categories: lean duplex, duplex, super duplex and hyper duplex. Please note that we have a minimum order value of £10,000.

Precision re-rolled stainless steel strip products can be engineered to specific customer requirements with exceptionally short lead times. Based on our longstanding expertise, we can manufacture stainless steel strip to precise custom sizes, ultra-thin gauges and tightly controlled mechanical properties with any surface finish. We also work closely with Hamilton Precision Metals, part of AMETEK Specialty Metal Products, to produce stainless steel foils down to 1.5 microns (.000060”) thickness. Standard Alloys We manufacture stainless steel strip in a variety of chemical and mechanical properties, expertly engineered to your exacting specifications. High performance stainless steel strip material includes: Austenitic: 300 series Martensitic: 400 series Ferritic: 400 series PH Grades 17-7PH®, 17-4PH® Additional options available on request

Make the perfect first impression with a high quality, custom made explainer video for your business, product, service or idea

CP Titanium is selected for its favorable strength to weight ratio and excellent corrosion resistance. Two levels of purity permit a choice of finish strength. The alloy can be formed from the annealed temper. Severe forming may be aided by an intermediate stress relief at 1000°F. Stress relieving may be appropriate after severe cold forming to remove residual stresses. Welding should be performed with inert gas shielded arc or spot welding. Welding with active gases, coatings, or fluxes must be avoided to prevent embrittlement. Available Sizes: CP Titanium is available from Hamilton Precision Metals as strip product from 0.0005” to 0.025” (0.0127 mm to 0.635 mm) and widths up to 12.0” (304.8 mm). A foil product is available as thin as 0.000085” (0.002159 mm) and widths of 4.0” (101.6 mm) maximum. The material conforms to ASTM F67, ASTM B265, AMS 4902 and UNS R50250,R50400. Density:0.163 lbs/cu.in. Melting Point (Approx.):1660°C Electrical Resistivity @ R.T.:56 Microhm·cm Thermal Expansion Coefficient (0 to 100°C):8.6 x 10-6/°C Thermal Expansion Coefficient (0 to 315°C):9.2 x 10-6/°C Thermal Conductivity @ R.T.:16.0 W/m·K

Titanium exhibits a unique combination of properties including excellent corrosion resistance, high temperature resistance, and outstanding strength to weight ratios. Titanium is produced as commercially pure or alloyed. Commercially pure titanium is typically used in implantable medical applications whereas the titanium alloys are produced with the addition of vanadium or aluminum for applications such as aerospace. Hamilton Precision Metals processes strip and foil products in Titanium CP (Grade 1, Grade 2, Grade 4) and Titanium 3Al-2.5V (Grade 9).

Ti Grade 9 is a near alpha, alpha-beta alloy, sometimes referred to as “half-6-4.” It offers 20 to 50% higher tensile strength than the commercially pure titanium at room and elevated temperatures. It is much more amenable to cold working than Ti 6AI/4V alloy and can be cold worked 75 to 85% to result in moderately high strength and good ductility The alloy can be formed from the annealed temper. Severe forming may be aided by an intermediate stress relief. Stress relieving may be appropriate after severe cold forming to remove residual stresses. Weldability and corrosion resistance is very similar to commercially pure titanium. Welding should be performed with inert gas shielded arc or spot welding.Welding with active gases, coatings, or fluxes must be avoided to prevent embrittlement.

AMETEK Specialty Metal Products uses a wrought powder metallurgical process to ensure the highest purity finished products. Our main strengths lie in the processing of Nickel, Iron and Cobalt containing alloys amongst other available materials. The processing of these materials begins with the consolidation of powder through a roll compaction process and followed by a controlled atmosphere sintering. Further reduction of the material is performed solely under cold working temperatures to reduce the introduction of non-metallics and annealing is performed under controlled atmospheres. AMETEK Strip Products are produced in ranges between .002” (0.05mm) and .080” (2.03mm) thicknesses in a full range of tempers and widths to 22” (558.8mm) while maintaining special capabilities to produce materials outside of these ranges for special applications. This process lends itself to the production of small but easily reproducible lots of highly specialized alloys

Crafting compelling corporate videos for B2C & B2B companies that elevate brands, engage audiences, and drive results. Let's tell your story!